Static Conditions Research Articles

Effects of Leading-Edge Blowing Control and Reduced Frequency on Airfoil Aerodynamic Performances

Abstract Airfoil leading-edge fluid-blowing control is computationally studied to improve aerodynamic efficiency. The fluid injection momentum coefficient Cμ (the ratio of injection to incoming square velocities times the slot's width to airfoil's half chord length) varies from 0.5% to 5.4%. Both static and dynamic conditions are investigated for a NACA0018 airfoil at low speed and Reynolds number of 250 k based on the airfoil's chord length. The airfoil is dynamically pitched at a reduced frequency (the pitching tangential speed to the freestream speed ratio), varying between 0.0078 and 0.2. Reynolds-averaged Navier–Stokes (RANS) and unsteady RANS (URANS) is used in the simulations as based on the Transition SST and Spalart–Allmaras models, generally achieving good agreement with experimental results in lift and drag coefficients and in the pressure coefficient distributions along the airfoil. It is found that oscillating the airfoil can delay stall, as expected, in dynamic stall (DS). Leading-edge blowing control can also significantly delay stall both in static and dynamic conditions as long as sufficient momentum is applied to the control. On the other hand, for a small Cμ such as 0.5%, the leading-edge control worsens the performance and hastens the appearance of stall in both static and dynamic conditions. The airfoil's oscillation reduces the differences between pitch-up and pitch-down aerodynamic performances. Detailed analysis of vorticity, pressure, velocity, and streamline contours is given to provide plausible explanations and insight to the flow.

Experimental evaluation of alternative ceiling-based ventilation systems for long-range passenger aircraft

AbstractAlternative ventilation technology bricks, such as ceiling-based, sidewall-based or floor-based ventilation, are of high interest in terms of manufacturing and customization benefits for passenger aircraft. Two novel ventilation systems and state-of-the-art Mixing Ventilation (MV) were experimentally investigated under static conditions in a ground-based research facility. In case of Micro-Jet Ventilation, a perforated ceiling brings the air into the cabin as localized micro-jets with high momentum. Further, Low-Momentum Ceiling Ventilation characterized by a low-momentum air supply through planar and large-surface inlets is investigated. The measurement techniques and the test matrix were designed in order to quantify and evaluate thermal comfort, local air quality and energy efficiency of the ventilation concept. The results proved that there is not one single ventilation concept which optimizes all challenges: air quality, thermal comfort and energy efficiency. Both advantages and disadvantages were found for each ventilation system. In terms of technology bricks, the following main results were found: The average local age-of-air was between 5 and 14%, depending on the boundary conditions. It was lower for the ceiling-based concepts compared to state-of-the-art MV. At the same time the average CO2 concentration decreased by 7–14% for the ceiling-based concepts compared to MV. The local velocities in the vicinity of the passengers were similar for cruise conditions, whereas they decreased by up to 38% in case of hot-day-on-ground conditions for ceiling-based ventilation compared to MV. On the other hand, the heat removal efficiency was low for all concepts and the temperature stratification increased in case of ceiling-based ventilation.

Evolutionary game analysis on collaborative logistics diffusion considering diminishing marginal utility under dynamic productivity

Reducing carbon emissions in the transportation sector is crucial for sustainable practices, with collaborative logistics diffusion playing a significant role in promoting energy-saving and emission-reduction strategies. This paper introduces an evolutionary game model to analyze collaboration between manufacturers and logistics service providers (LSPs), using the Hotelling quadratic curve model to measure the diminishing marginal utility of basic profits. Initially, a static strategy leads to a cyclic evolution without reaching the evolutionary stable strategy (ESS), reflecting competitive dynamics under static productivity conditions where neither party gains a lasting advantage, leading to periodic adjustments in strategies. The Cobb-Douglas function models a dynamic productivity strategy that regulates the extra benefits of collaborative logistics and penalties for 'free-riding.' This strategy demonstrates an inward spiral convergence towards the ESS, showing that adaptive mechanisms enable manufacturers and LSPs to align interests and achieve equilibrium. Enhanced benefits from collaborative logistics promote a stable and cooperative ecosystem, discouraging free-riding and enhancing cost efficiency. Moreover, increased investment by manufacturers not only strengthens their position but also fosters an environment conducive for LSP participation, expediting collaborative logistics diffusion and minimizing potential losses.

Bioactivity of radiopaque 45S5 bioactive glass with progressive additions of Bi2O3: A dissolution study under static conditions

Bioactivity of radiopaque 45S5 bioactive glass with progressive additions of Bi2O3: A dissolution study under static conditions

Describing the cellular impact of IQOS™ smoke extract and vibration on human vocal fold fibroblasts

ObjectivesThe isolated or combined effects of vibration and smoke extract (SE) from the IQOS™ “heat-not-burn” technology on human vocal fold fibroblasts (hVFF) were evaluated in an in vitro setting in order to elucidate their influence on vocal fold (patho-) physiology. Study DesignExperimental pilot study using intervention with IQOS™-SE in vitro. MethodsImmortalized hVFF were exposed to IQOS™-SE or control medium under static or vibrational conditions. A phonomimetic bioreactor was used to deliver vibrational patterns to hVFF over a period of 5 days. Cytotoxicity was quantified by lactate dehydrogenase assay. Effects on extracellular matrix production, inflammation, fibrogenesis, and angiogenesis were assessed by reverse transcription-quantitative polymerase chain reaction, Western Blot, enzyme-linked immunosorbent assay, and Magnetic Luminex assays. ResultsWe observed significant changes induced either by IQOS™-SE exposure alone (matrix metalloproteinase 1, fibronectin, cyclooxygenase (COX)1, interleukin-8 gene expression), or by the combination of IQOS™-SE and vibration (hyaluronidase 2, COX2, interleukin-8 protein levels, vascular endothelial growth factor D). ConclusionShort-term in vitro exposure of hVFF to IQOS™-SE did not result in cytotoxicity and reduced the gene expression of measured inflammation mediators, but had no effect on their protein expression. However, the clinical effects of long-term IQOS™ use are still not known and further research is needed in order to asses, if IQOS™ is in fact less harmful than conventional cigarettes.

New Insights into the Role of Thiol Collectors in Malachite Flotation

Malachite is one of the most important copper-bearing oxide minerals; however, it shows poor floatability prior to sulfidization under the thiol collector system. This study investigated the reasons for the low recovery of malachite flotation without sulfidization. The results of adsorption capacity and contact angle test indicated that the malachite surface could adsorb a sufficient amount of the collector, obviously increasing the hydrophobicity of the malachite surface under static conditions. By measuring the amount of inorganic carbon in the flotation solution, it was found that the amount of inorganic carbon in the solution increased significantly when the thiol collectors were added into pulp, which could be attributed to the induced dissolution of the malachite surface by thiol collectors. Solubility tests further demonstrated that the copper ions released from the natural dissolution of malachite proved difficult in regard to reactions with thiol collector to form precipitates; however, the thiol collector induced the dissolution of malachite surface, and so the hydrophobic complexes’ copper-collector could not firmly adsorb on the mineral surface. Fourier transform infrared (FTIR) analysis revealed that thiol collectors do not adsorb stably on malachite surfaces. This was considered to be a substantial reason for the poor performance of malachite flotation without sulfidization.

Researching the Influence of Preload on Vibration Characteristics in the Ballistic Recorder Vibration Damping System

In this study, the vibration characteristics of a bullet-loaded recorder’s vibration damping system under various preload conditions are investigated through theoretical analysis, numerical simulations, and experimental verification. The findings indicate that the inclusion of a polyurethane elastomer vibration damping buffer layer between the cartridge and the recorder, along with the application of a specific preload, significantly reduces the amplitude of vibration acceleration transmitted to the recorder’s interior. This, in turn, enhances the overload resistance of the cartridge’s internal circuit. Numerical simulation results and theoretical analysis suggest that increasing the preload on the buffer material between the elastomer and the recorder reduces both the frequency ratio and damping ratio of the damping system. This reduction further decreases the amplitude of vibration transmitted to the recorder. However, excessively high preload generates substantial compressive stress within the recorder under static conditions, intensifying during the projectile’s accelerated movement. As a consequence, deformation and damage occur to the internal circuitry. Therefore, ensuring that the recorder possesses the structural strength necessary to withstand increased preload is crucial. This balancing act improves the recorder’s resistance to shock, vibration, and overload, while also preventing excessive stress-induced damage.

Development of a bio-inspired wound model for debridement training

AbstractWound debridement is commonplace in expediting wound healing in the clinic. Despite this, there are limited resources available for simulation training for practitioners prior to facing real-life patients. Typically, citrus peels or porcine skin are employed in a vain attempt to improve debridement proficiency, yet these fail to provide a realistic experience of the textures and consistencies of wounds. Therefore, there is a clear unmet need for a safe and effective tool that can facilitate hands-on learning under the instruction of an experienced debrider. To fill this niche, a life-like wound model was designed and developed, featuring leathery necrotic eschar, an intermediary sloughy layer, and a rough granulation tissue in the bottommost layer, all within a healthy skin base. The healthy tissue portion of the model was designed to exhibit similar mechanical properties to those found in human skin. Likewise, the sloughy layer was viscous enough to remain within the model under static conditions yet could be removed using any appropriate debriding tool synonymous with real slough. Mechanical testing of the necrotic eschar revealed brittle fracture behaviour, akin to what is observed in patients. Each layer of the wound model provided the visual and haptic feedback of how it would look and feel to debride a patient’s wound in the clinic, giving invaluable experience for potential trainees in a safe and effectual way. It is envisaged that these models can be developed in a personalised way to suit the individual needs of the user, such as incorporating underlying models of bone or tendon, while retaining the key elements of the wound, which make it successful. This model is proposed as an important step forward in bridging the gap between becoming a newly qualified debriding practitioner and encountering the first wound in the clinic, subsequently improving the confidence of the debrider and enhancing patient outcomes.

Improved Durability of a Modular Axial Fixator for Stable and Unstable Proximal Femoral Fractures: A Patient-Specific Finite Element Analysis

Abstract Objectives: Femoral neck fractures, comprising 8-10% of all bodily fractures in the elderly, often necessitate alternatives to extensive surgical interventions. Despite limited research, external fixators are considered promising. This study evaluates the design and durability of a novel Modular Axial Fixator (MAF) for stable and unstable proximal femoral fractures, using numerical method-based engineering analysis. Methods: Employing patient-specific CT scan data, 3D solid modelling, and finite element analysis (FEA), the MAF-bone fixation is examined in eight simulation scenarios under static loading conditions. Results: FEA results show a peak femur head displacement of 7.429 mm in FEA 001, with Schanz screw no. 2 reaching the maximum equivalent stress at 431.060 MPa in FEA-006. Notably, the 7.429 mm displacement improves stability compared to previous studies, yet interfragmentary movement surpasses the 100-200 μm reference range for primary fracture healing, posing challenges to direct healing despite enhanced stability. Conclusion: This study validates the durability of the innovative MAF for femoral neck fractures through engineering simulations. It contributes to understanding MAF durability issues, with implications for improving medical implant design in the industry. Simulation results offer opportunities for optimising structure and production, enhancing the MAF's design, and ultimately benefiting medical implant manufacturing.

CFD Simulations and Phenomenological Modelling of Aerodynamic Stall Hysteresis of NACA 0018 Wing

Computational simulations of three-dimensional flow around a NACA 0018 wing with an aspect ratio of AR=5 were carried out by using the Unsteady Reynolds-Averaged Navier–Stokes (URANS) equations with the Shear-Stress Transport turbulence model closure. Simulations were performed to capture aerodynamic stall hysteresis by using the developed pseudo-transient continuation (PTC) method based on a dual-time step approach in CFD OpenFOAM code. The flow was characterized by incompressible Mach number M=0.12 and moderate Reynolds number Re=0.67×106. The results obtained indicate the presence of noticeable aerodynamic hysteresis in the static dependencies of the force and moment coefficients, as well as the manifestation of bi-stable flow separation patterns, accompanied by the development of asymmetry in the stall zone. The URANS simulation results are in good agreement with the experimental data obtained for the NACA 0018 finite-aspect-ratio wing in the low-speed wind tunnel under the same test conditions. A new phenomenological bifurcation model of aerodynamic stall hysteresis under static and dynamic conditions is formulated and is proven to be able to closely match the experimental data.

Experimental Study on Dynamic Mechanical Performance of Post-Fire Concrete Confined by CFRP Sheets

Impact tests on post-fire concrete confined by Carbon Fiber-Reinforced Polymer/Plastic (CFRP) sheets were carried out by using Split Hopkinson Pressure Bar (SHPB) experimental setup in this paper, with emphasis on the effect of exposed temperatures, CFRP layers and impact velocities. Firstly, according to the measured stress-strain curves, the effects of experiment parameters on concrete dynamic mechanical performance such as compressive strength, ultimate strain and energy absorption are discussed in details. Additionally, temperature caused a softening effect on the compressive strength of concrete specimens, while CFRP confinement and strain rate play a hardening effect, which can lead to the increase in dynamic compressive strength by 1.8 to 3.6 times compared to static conditions. However, their hardening mechanisms and action stages are extremely different. Finally, nine widely accepted Dynamic Increase Factor (DIF) models considering strain rate effect were summarized, and a simplified model evaluating dynamic compressive strength of post-fire concrete confined by CFRP sheets was proposed, which can provide evidence for engineering emergency repair after fire accidents.

A mechanical-assisted post-bioprinting strategy for challenging bone defects repair

Bioprinting that can synchronously deposit cells and biomaterials has lent fresh impetus to the field of tissue regeneration. However, the unavoidable occurrence of cell damage during fabrication process and intrinsically poor mechanical stability of bioprinted cell-laden scaffolds severely restrict their utilization. As such, on basis of heart-inspired hollow hydrogel-based scaffolds (HHSs), a mechanical-assisted post-bioprinting strategy is proposed to load cells into HHSs in a rapid, uniform, precise and friendly manner. HHSs show mechanical responsiveness to load cells within 4 s, a 13-fold increase in cell number, and partitioned loading of two types of cells compared with those under static conditions. As a proof of concept, HHSs with the loading cells show an enhanced regenerative capability in repair of the critical-sized segmental and osteoporotic bone defects in vivo. We expect that this post-bioprinting strategy can provide a universal, efficient, and promising way to promote cell-based regenerative therapy.

Effect of Helichrysum italicum in Promoting Collagen Deposition and Skin Regeneration in a New Dynamic Model of Skin Wound Healing

Natural products have many healing effects on the skin with minimal or no adverse effects. In this study, we analyzed the regenerative properties of a waste product (hydrolate) derived from Helichrysum italicum (HH) on scratch-tested skin cell populations seeded on a fluidic culture system. Helichrysum italicum has always been recognized in the traditional medicine of Mediterranean countries for its wide pharmacological activities. We recreated skin physiology with a bioreactor that mimics skin stem cell (SSCs) and fibroblast (HFF1) communication as in vivo skin layers. Dynamic culture models represent an essential instrument for recreating and preserving the complex multicellular organization and interactions of the cellular microenvironment. Both cell types were exposed to two different concentrations of HH after the scratch assay and were compared to untreated control cells. Collagen is the constituent of many wound care products that act directly on the damaged wound environment. We analyzed the role played by HH in stimulating collagen production during tissue repair, both in static and dynamic culture conditions, by a confocal microscopic analysis. In addition, we performed a gene expression analysis that revealed the activation of a molecular program of stemness in treated skin stem cells. Altogether, our results indicate a future translational application of this natural extract to support skin regeneration and define a new protocol to recreate a dynamic process of healing.

Hip joint center lateralization minimally affects the biomechanics of patient-specific flanged acetabular components: A computational model.

Patient-specific flanged acetabular components are utilized to treat failed total hip arthroplasties with large acetabular defects. Previous clinical studies from our institution showed that these implants tend to lateralize the acetabular center of rotation. However, the clinical impact of lateralization on implant survivorship is debated. Our goal was to develop a finite element model to quantify how lateralization of the native hip center affects periprosthetic strain and implant-bone micromotion distributions in a static level gait loading condition. To build the model, we computationally created a superomedial acetabular defect in a computed tomography 3D reconstruction of a native pelvis and designed a flanged acetabular implant to address this simulated bone defect. We modeled two implants, one with ~1 cm and a second with ~2 cm of hip center lateralization. We applied the maximum hip contact force and corresponding abductor force observed during level gait. The resulting strains were compared to bone fatigue strength (0.3% strain) and the micromotions were compared to the threshold for bone ingrowth (20 µm). Overall, the model demonstrated that the additional lateralization only slightly increased the area of bone at risk of failure and decreased the areas compatible with bone ingrowth. This computational study of patient-specific acetabular implants establishes the utility of our modeling approach. Further refinement will yield a model that can explore a multitude of variables and could be used to develop a biomechanically-based acetabular bone loss classification system to guide the development of patient-specific implants in the treatment of large acetabular bone defects.

Magnetic focusing sensor and its characterizations of defect non-destructive testing for ferromagnetic steel plate

The fast development in precision manufacturing and product quality inspection of ferromagnetic material desperately demands that the defect determining the performance, service life and reliability of the mechanical part should be accurately sensed, detected and evaluated. However, conventional defect detection methods and related magnetic induction sensors are usually characterized with low accuracy in small defect detection, which makes the non-destructive testing (NDT) for ferromagnetic material full of challenges. Thus, a new magnetic focusing sensor is proposed and designed for the precision defect detection of ferromagnetic steel plate here. First, the theoretical principle analysis of the magnetic focusing sensor is introduced, and the preliminary finite element modeling (FEM) is conducted to demonstrate the feasibility of the magnetic focusing sensor in tiny defect inspection. Then, both the static and coupling dynamic characterizations of the magnetic focusing sensor are investigated using the FEM method. The optimal structural parameters of the magnetic focusing (MF) sensor in static conditions are summarized. Furthermore, the effects of the dynamic movement of the MF sensor on the multi-physical fields of the magnetization field, electric field, electromagnetic attraction force field and thermal field are all revealed. Finally, experiments regarding the performance evaluation and comparison between the MF sensor and other two magnetic flux leakage (MFL) sensors are conducted, and the prominent capabilities of accurate and precise defect detection for the MF sensor is demonstrated through the defect detection with different sizes. The effectiveness and feasibility of the MF sensor in detecting tiny defects on ferromagnetic object, as well as its great potential for practical application is therefore validated. Additionally, the main conclusions, advantages of the MF sensor are summarized and the future work is discussed.

Removal of movement artifacts and assessment of mental stress analyzing electroencephalogram of non-driving passengers under whole-body vibration

The discomfort caused by whole-body vibration (WBV) has long been assessed using subjective surveys or objective measurements of body acceleration. However, surveys have the disadvantage that some of participants often express their feelings in a capricious manner, and acceleration data cannot take into account individual preferences and experiences of their emotions. In this study, we investigated vibration-induced mental stress using the electroencephalogram (EEG) of 22 seated occupants excited by random vibrations. Between the acceleration and the EEG signal, which contains electrical noise due to the head shaking caused by random vibrations, we found that there was a strong correlation, which acts as an artifact in the EEG, and therefore we removed it using an adaptive filter. After removing the artifact, we analyzed the characteristics of the brainwaves using topographic maps and observed that the activities detected in the frontal electrodes showed significant differences between the static and vibration conditions. Further, frontal alpha asymmetry (FAA) and relative band power indices in the frontal electrodes were analyzed statistically to assess mental stress under WBV. As the vibration level increased, EEG analysis in the frontal electrodes showed a decrease in FAA and alpha power but an increase in gamma power. These results are in good agreement with the literature in the sense that FAA and alpha band power decreases with increasing stress, thus demonstrating that WBV causes mental stress and that the stress increases with the vibration level. EEG assessment of stress during WBV is expected to be used in the evaluation of ride comfort alongside existing self-report and acceleration methods.

Effect of TGF-β3 on wound healing of bone cell monolayer in static and hydrodynamic shear stress conditions

IntroductionWound healing is characterized as a complicated and sophisticated biological process through which tissue heals and repairs itself after injury. However, the normal wound healing process relies on different growth factors as well as the presence of an accurate cytokine level to ensure appropriate cellular responses. In the case of wound healing, the effects of various growth factors have been studied, but the effects of transforming growth factor beta (TGF-β) on wound healing have been found to be more significant because of its broad spectrum of impacts on healing the wounded tissues or skins.MethodsIn the current study, the impact of TGF-β3 in bone cells’ wound healing was examined in vitro. Furthermore, the activities and characteristics of TGF-β3, as well as those of related growth factors throughout this wound healing process, were studied under hydrodynamic shear stress conditions as well as static conditions of cultured bone cells.ResultsWe demonstrated that a positive outcome of TGF-β3 treatment was found after 24 h under a static condition, while TGF-β3 treatment was found to be effective under a dynamic condition for wound closure. In the case of the dynamic condition, a full wound closure was obtained after 18 h in both the control and TGF-β3 treatment, while in the case of static conditions, wounds were found to remain open, even after 24 h, for both the control and TGF-β3 treatment. Additionally, in the static condition, the wound closure rate with TGF-β3 treatment was found to be quicker than that of the control flask, which implies that wound healing can be postponed in the static condition. In the dynamic condition, the wound healing process became more rapid in a cultured cell environment.ConclusionThe synergistic effect of TGF-β3 and hydrodynamic shear stress conditions had a positive impact on increasing wound healing and improving the rate of wound closure.

Multiphysics modeling of magnetoelectric composite disks by a 2D axisymmetric finite element approach

A 2D axisymmetric finite element multiphysics model is proposed to study magnetoelectric composite disks. This modeling approach includes a nonlinear magneto-elastic model to replicate the behavior of magnetostrictive materials under static conditions. Additionally, it offers a harmonic regime resolution that considers frequency dependence, including the implicit inclusion of eddy currents in the formulation, as well as electrical load. To validate the model, simulation results regarding the dependence of the static magnetic field and frequency are presented and compared with experimental measurements from literature.

MRI Measurements of the Cartilage Contact Pattern, Contact Area, and Contact Centroid of the Glenohumeral Joint During Abduction Under Static Conditions In Vivo

MRI Measurements of the Cartilage Contact Pattern, Contact Area, and Contact Centroid of the Glenohumeral Joint During Abduction Under Static Conditions In Vivo

Examination of the Bactericidal and Fungicidal Activity of Bacillus amyloliquefaciens M Isolated from Spring Waters in Bulgaria

In order for a strain to be considered a probiotic or suitable plant bioprotective agent, it must have proven antimicrobial activity against pathogenic bacteria and phytopathogenic fungi. Bacillus amyloliquefaciens M exhibited significantly high antifungal activity against pathogenic fungi of the genera Aspergillus, Penicillium, Fusarium, and Sclerotinia; yeasts of the genera Candida and Saccharomyces; as well as high antibacterial activity against pathogens of the genera Escherichia, Salmonella, Staphylococcus, Listeria, Pseudomonas, and Bacillus. The manifested antimicrobial activity was influenced by the composition of the growth medium. The antifungal activity of the strain was investigated at growth temperatures of 30 °C and 37 °C, and at different pH values in aerobic and anaerobic cultivation, under static and dynamic culturing conditions. High antifungal activity was observed at the 24th h on both growth media (LBG broth and MPB broth) at pH = 6 and pH = 7 in aerobic and anaerobic cultivation. Bacillus amyloliquefaciens M produced antibiotic substances at pH > 5.0, and the antibiotic substances were either secreted into the medium or associated with the cell surface. Four compounds with different antifungal activity and different Rf values were registered through thin-layer chromatography (Rf1 = 0.47; Rf2 = 0.55; Rf3 = 0.67; and Rf4 = 0.75), two of the compounds were ninhydrin-positive. Bacillus amyloliquefaciens M was cultured in a bioreactor with stirring, and the parameters of the growth kinetics and the sporulation kinetics have been modeled. A spore concentrate of Bacillus amyloliquefaciens M has been obtained. In further research, the efficiency of the concentrate as a plant bioactive agent will be tested.